制氮機是如何對碳分子篩進行簡易轉化？

碳分子篩的更換是耗材問題的解決，考慮到制氮機工作上的特性，因此我們在進行轉化的時候需要用到簡易的方法，下面就讓山東制氮機廠家的小編為你詳細介紹下制氮機是如何對碳分子篩進行簡易轉化的?

The replacement of carbon molecular sieve is the solution to the problem of consumables. Considering the working characteristics of the nitrogen generator, we need to use a simple method when we carry out the conversion. Let's let the editor of Shandong nitrogen generator manufacturer introduce in detail how the nitrogen generator carries out the simple conversion of carbon molecular sieve?

1、電源被切斷。取代碳分子篩的制氮機安全運行的前提是先切斷電源!記住這一點。停止供應壓縮空氣，卸載制氮機系統內部壓力，直至所有壓力表歸零，并切斷系統電源。

1. The power was cut off. The prerequisite for the safe operation of the nitrogen generator replacing carbon molecular sieve is to cut off the power first! Remember this. Stop the supply of compressed air, unload the internal pressure of the nitrogen generator system until all pressure gauges return to zero, and cut off the power supply of the system.

2. 
   

2、卸下制氮機吸附塔的頂蓋，提前準備好拆卸扳手!

2. Remove the top cover of the adsorption tower of the nitrogen generator and prepare the spanner in advance!

3、取下制氮機不銹鋼絲網!

3. Remove the stainless steel wire mesh of nitrogen generator!

4、清除工作完成后，加入3厘米厚的椰墊過濾，用直徑為5MM的氧化鋁在吸附塔底部預鋪5厘米厚，然后進行碳分子篩裝填。

4. After the removal, add 3 cm thick coconut mat for filtration, pre lay 5 cm thick alumina with diameter of 5 mm at the bottom of the adsorption tower, and then carry out carbon molecular sieve loading.

5、填充至頂部，用錘子或振動設備振動吸附塔，使碳分子篩之間的堆積密度達到620-640千克/立方米，更新頂部的椰墊和不銹鋼絲網，覆蓋吸附塔的頂部，用長螺栓緊固至常規位置，更新所有高于8.8的高強度螺栓。

5. Fill to the top, vibrate the adsorption tower with hammer or vibrating equipment to make the bulk density between the carbon molecular sieves reach 620-640 kg / m3, update the coconut mat and stainless steel wire mesh on the top, cover the top of the adsorption tower, fasten to the normal position with long bolts, and update all high strength bolts higher than 8.8.

6、復位后，調試制氮機。調試包括接頭肥皂水的泄漏檢測、工作狀態和性能指標。請參考制氮機的操作說明!

6. After reset, debug the nitrogen generator. The debugging includes the leakage detection, working state and performance index of the joint soapy water. Please refer to the operating instructions of the nitrogen generator!

更多關于制氮機的訊息，歡迎登錄網址進行詳細了解http://www.matsteinwede.com

For more information about nitrogen generator, please visit our website for more information http://www.matsteinwede.com